- Order number: SW11090
Switching power supply for digital centers, for example for the DCC central unit of Massoth or the 30B booster digital central unit of MD-Electronics
Switching power supply for various applications such as garden railways, analogue driving or DCC systems and 3D printers,
The power supply for the Massoth Dimax control unit was tested successfully and for months, as well as on the Booster 30B from MD-Electronics.
Nevertheless, we do not guarantee our statements here, but only describe what we have found on the net on the Internet and about our experiences with it in the garden railway sector. We explicitly do not recommend the use of the article for the layman or for children, since the housing would have to be additionally installed in a protective housing. Who uses the power supply, must ensure that children's hands do not come to the contacts. For representations please pull out the mains plug. Outdoor use is prohibited. We do not warrant the use of this product in conjunction with a Massoth Dimax DCC Control Center, although we know it will work properly with it. If you do not have the money for a Massoth switched-mode power supply, you can start with this inexpensive power supply and try it at your own risk.
Disconnect power supply brand XKTTSUEERCRR China.
Since the Schaltnertzteil has no cable connections with plug, it is not a finished functional unit and not a finished machine in the sense of the Declaration of Conformity. It is therefore offered as a kit. To make the power supply functional, you will need a 230 volt connection cable with mains plug that you must connect to the corresponding terminals. Such pre-assembled power plugs with Schukostecker are available for 6 and 16 amp in the trade.
ASIN: B01IMQ1Q4C
Material of the housing: Aluminum
Input voltage: 230V / 110V AC
Output voltage: 3 times 24V DC
Output current: max. 15A
Working temperature: 0 ~ 40 ℃
Protection: short circuit protection, overheating protection, overvoltage protection
Suitable for most devices with DC 24V. Only for inside!
The device should be installed in a protective housing.
Protective cover folds over the cable clamp strip
High voltage stability
24V DC, adjustable from 19.5V to 27V
High performance, safe and durable.
Caution: The voltage of this device can be switched (110V / 230V) via a slide switch on the side of the device. Before use, please check that the voltage is set correctly.
The switching power supply has a 60mm fan. This will automatically switch on and off depending on the power supply temperature.
PWM control via TL494 circuit. DCC decoders and RC controllers use PWM control for the motor current.
15A are kept but device can get warm. Therefore, one should use the full load only in the short term. The continuous use up to 10 amps is not a problem. For the Massoth Dimax control panel, we recommend setting this to 7 amps.
In garden railways, it is possible to connect three controllers with 3 track sections in analog mode to terminals 3.
In digital mode you can connect 2 Dimax control panels, each set to 7 amps. Since you can connect 3 navigators to each Dimax central unit, you can connect a total of 6 navigators and thus let 6 locomotives travel separately.
Application for the garden railway in analogue mode:
To a power supply can be e.g. connect three PIKO Speed Controllers 35002 (max 22V 5A DC) or 35006 (max 22V 1.6A). To do this, the regulator on the switching power supply must be turned down to 22 volts by means of a screwdriver.
With shorts you should be very careful, since up to 15A can flow. Here, the short-circuit protection will jump in.
Additional fast fuses, as they are known from the automotive industry, and which we offer with fuse boxes, can be used here
The switching power supply must not be used outdoors. Only long connecting cables from the room to the speed controllers should be used.
Instead of PIKO speed controllers, PWM speed controllers can also be purchased from the electronics trade. Be sure to use at least one with a frequency of 15 KHz.
Application for the garden railway in digital mode
The device can be connected to a Massoth DiMAX 1210Z digital control unit.
With 24 Volt and an output current of 13A, it meets exactly the conditions set by Massoth
Manufacturer:
Business name: Shenzhen Haotian Hengrui Maoyi Youxian Gongsi
Business Type: LTD
Company registration number: 440301112939206
UStID: GB276896433
Phone number: +86 (0) 75582853236
1515 B Dong 2 DanYuan XingHeShiJi
CaiTianLu FuTianJieDao FuTianQu
ShenZhen
GuangDong
518016
China
brand
XKTTSUEERCRR
Product weight
762 g
product dimensions
21.5 x 5 x 11.4 cm
model number
R2-6BUR-PGPH
item number
R2-6BUR-PGPH
tension
24 volts
Power supply and plug type
Wired
Batteries included
No
Batteries necessary
No
version
2G10
power consumption
up to 360 watts